Sheet G-01 · About the drawing office

A lamp, a scale rule, and a Tuesday-morning queue of other people’s kitchens.

Millurano is a single drawing office on Grand Brook Drive in Greenwood, Arkansas. It exists to turn rough intent into dimension, so a shop can cut on the day it means to.

Fig. 02 · Why the office exists

Most callbacks begin with a dimension nobody closed.

Drafting desk with scale rule and a cabinet elevation on vellum under a lamp
Fig. 02a · The desk

Millwork fails quietly. A filler strip goes unaccounted for, a drawer face is cut an eighth narrow, a hinge lands where the adjacent door swings through. By the time anyone notices, the material is cut and the install date is fixed.

Millurano was set up to move that discovery to the drawing board, where it costs a pencil line instead of a sheet of birch ply. The office draws cabinetry and millwork and nothing else. It does not fabricate, install or sell product, so the only thing it has to get right is the sheet.

The work is issued to the people who stand at the saw: cabinet shops that need cut-ready files, contractors who need approval and release sets, and interior designers whose intent has to become buildable dimension.

The sheet is the product. Everything else in the office exists to make it correct.

Fig. 03 · Drafting standard

Four conventions every sheet is held to.

They are written down, applied to every project and never waived for a deadline. That is why a sheet from March reads like a sheet from October.

STD-01 · Dimension 1/32″

Inches, drawn to the thirty-second

Dimension strings are chained and closed against the overall. Where a run does not sum, the discrepancy is noted on the sheet, never absorbed silently.

STD-02 · Layers 4

One layer convention, always

A-CAB, A-DIM, A-HDW and A-CUT carry the work, so any machinist opening a file finds the same structure.

STD-03 · Hardware 32 mm

Line-bore system respected

Hinge plates, slides and pulls are placed on the system grid and checked against every neighbouring part before release.

STD-04 · Revision Rev A→

One letter, one version

Every change is issued under a new revision letter on the title block, so the bench never holds two truths about the same elevation.

Fig. 04 · Revision log of a typical job

From first email to released set, as the office runs it.

Read as a revision block: each entry is a stage a project passes through, in order.

AIntake

The brief is read, not skimmed

Sketches, field notes and the spec are checked for gaps. Questions go back in a single list, with a fixed fee stated in writing.

BKickoff

Half the fee opens the file

The project is assigned a number and a title block, and joins the Tuesday-to-Saturday drafting queue.

CDrafting

Modeled once, drawn from the model

Plans, elevations and sections come from the same model as the cut list, so they cannot drift apart.

DCheck

Read back the way the shop reads it

Strings close, parts reconcile, hardware clears. Nothing is issued until all three agree.

ERelease

Balance due, files delivered

The final set arrives as plotted PDF and layered DXF / DWG, with the cut list and hardware schedule.

Fig. 05 · Working terms

Terms on one sheet, agreed before the first line.

The firm’s terms are short enough to read in a minute, and they do not change after kickoff.

Rolled drawings and a tape measure beside a cut birch panel
Fees
Fixed per project, from $385
Payment
Half at kickoff, balance on release
Revisions
Rounds stated per package; then $62 / hr
Rush
+30%, 48-hour turn
Ownership
Drawings are yours once paid
Hours
Tue–Sat 8:30am–7pm
Sunday
11am–3pm
Monday
Closed; files queue for Tuesday
Next sheet in the queue

Send the sketch. The fee comes back in writing.

See the packages and their prices on the services page, or put the project in front of the drafting desk directly.

Call the desk Get a quote